Mechanics of Materials
Stress, strain, torsion, bending, buckling, and failure criteria.
Stress, Strain, and Material Behavior
Why Study Mechanics of Materials? Every structure — bridges, buildings, aircraft, chips, bones — must carry loads without failing. Mechanics of materials gives engineers the tools to predict when a...
Why Study Mechanics of Materials?
Every structure — bridges, buildings, aircraft, chips, bones — must carry loads without failing. Mechanics of materials gives engineers the tools to predict when a structure will bend, break, or buckle. It bridges the gap between statics (forces in equilibrium) and real material behavior (deformation, yielding, fracture).
Normal Stress and Strain
Stress σ is force per unit area:
σ = F / A
Units: pascals (Pa), or MPa (10⁶ Pa), or psi (pounds per square inch).
Strain ε is the fractional change in length:
ε = ΔL / L₀
Strain is dimensionless. Typical elastic strains in metals are 0.001 to 0.005 (0.1% to 0.5%).
Hooke's Law
For linear elastic materials, stress and strain are proportional:
σ = E × ε
E is Young's modulus — a material property.
| Material | E (GPa) |
|----------|---------|
| Rubber | 0.01-0.1 |
| Wood | 10 |
| Aluminum | 70 |
| Steel | 200 |
| Diamond | 1000 |
For a bar under axial load:
δ = F × L / (A × E)
This is the fundamental deformation formula.
Poisson's Ratio
When stretched in one direction, materials usually contract in the perpendicular directions:
ν = -ε_lateral / ε_axial
Typical values: 0.3 (steel), 0.33 (aluminum), 0.5 (rubber, incompressible).
Shear Stress and Strain
Shear stress τ acts parallel to a surface:
τ = V / A
Shear strain γ is the change in angle (radians):
τ = G × γ
where G = E / (2(1+ν)) is the shear modulus.
Stress-Strain Curve
For a typical ductile metal:
- Elastic region: linear, reversible, slope = E
- Yield point: σ_y, where plastic deformation begins
- Strain hardening: stress rises as the material deforms plastically
- Ultimate strength: σ_u, maximum stress
- Necking and fracture: material locally narrows and breaks
Ductile materials (steel) have large plastic strain. Brittle materials (cast iron, ceramics) fracture with little deformation.
Allowable Stress and Safety Factor
Design stress must be below yield:
σ_allow = σ_y / SF
Safety factors: 1.5-2 for well-understood loads, 3-4 for uncertain, 5+ for critical (pressure vessels, aircraft).
Thermal Stress
Temperature changes cause thermal strain:
ε_thermal = α × ΔT
If the material is constrained, thermal strain becomes thermal stress:
σ = -E × α × ΔT
where α is the coefficient of thermal expansion (CTE). Typical: 12 × 10⁻⁶ /°C for steel.
This is why bridges have expansion joints and railroad tracks can buckle on hot days.
Key Takeaways
- Stress = force / area; strain = ΔL / L
- Hooke's law: σ = Eε in the elastic region
- Poisson's ratio: lateral contraction under axial load
- Yield strength is the design limit for ductile materials
- Thermal expansion causes stress in constrained structures
- Safety factor accounts for uncertainty
Axial Loading and Torsion
Axial Loading of Bars A bar under axial load has uniform stress (away from load application points): σ = F / A δ = FL / (AE) For a bar with varying cross-section or load, integrate: δ = ∫₀^L...
Axial Loading of Bars
A bar under axial load has uniform stress (away from load application points):
σ = F / A
δ = FL / (AE)
For a bar with varying cross-section or load, integrate:
δ = ∫₀^L F(x) / (A(x) E) dx
Statically Indeterminate Problems
When equilibrium equations are not enough to find the reactions (too many supports), the problem is statically indeterminate. Add compatibility equations (deformations must be consistent).
Example: A bar fixed at both ends, loaded in the middle.
- Equilibrium: R_A + R_B = F
- Compatibility: total elongation = 0
- Compatibility equation: R_A L₁ / (AE) = R_B L₂ / (AE)
- Solve: R_A = F × L₂ / (L₁ + L₂)
Stress Concentrations
Holes, notches, and sudden changes in cross-section concentrate stress. The stress at the concentration is:
σ_max = K × σ_nominal
where K is the stress concentration factor (from tables).
Typical K values:
- Circular hole in a wide plate: K = 3
- Sharp notch: K = 5-10
- Sharp crack: K → ∞ (fracture mechanics needed)
Design rule: avoid sharp corners. Use fillets with radius ≥ 0.1 × the section width.
Torsion of Circular Shafts
A torque T applied to a circular shaft produces shear stress:
τ = T × r / J
where r is the radial distance and J is the polar moment of inertia:
J = π × d⁴ / 32 (solid)
J = π × (d_o⁴ - d_i⁴) / 32 (hollow)
Maximum shear stress at the outer surface:
τ_max = T × c / J
where c is the outer radius.
Angle of Twist
The shaft twists by:
φ = T × L / (J × G)
where G is the shear modulus. This is the torsion analog of axial deformation.
Power Transmission
Torsion is how shafts transmit power:
P = T × ω
where ω is angular velocity (rad/s). For a shaft running at N rpm:
ω = 2π × N / 60
Given a power P and speed N, find the required shaft diameter:
T = P / ω
d³ = 16 T / (π × τ_allow)
This is the basic shaft sizing equation.
Combined Loading
Real components often experience axial, bending, and torsion simultaneously. Use principal stresses to combine them.
For a point under σ_x and τ_xy, the principal stresses are:
σ₁,₂ = σ_x/2 ± √((σ_x/2)² + τ_xy²)
Maximum shear stress:
τ_max = √((σ_x/2)² + τ_xy²)
Use the von Mises or Tresca criterion to predict yielding:
- Tresca: yield when τ_max = σ_y / 2
- von Mises: yield when √(σ₁² - σ₁σ₂ + σ₂²) = σ_y
Key Takeaways
- Axial: δ = FL/(AE)
- Statically indeterminate problems need compatibility equations
- Stress concentrations multiply stress (K factor)
- Torsion: τ = Tr/J, φ = TL/(JG)
- Power: P = Tω, d³ = 16T/(πτ)
- Combined loads: use principal stresses
- Tresca and von Mises predict yielding
Bending of Beams
Beam Basics A beam is a slender member loaded perpendicular to its axis. It carries: Shear force V(x): internal force perpendicular to the axis Bending moment M(x): internal moment that bends the...
Beam Basics
A beam is a slender member loaded perpendicular to its axis. It carries:
- Shear force V(x): internal force perpendicular to the axis
- Bending moment M(x): internal moment that bends the beam
Sign Conventions
Standard convention:
- Positive V: forces the left section up
- Positive M: causes the beam to sag (concave up)
Relation Between Load, Shear, and Moment
dV/dx = -w(x) (w is distributed load, positive down)
dM/dx = V(x)
These differential relations are extremely useful:
- Slope of V diagram = -w
- Slope of M diagram = V
- M is maximum where V = 0
- Area under w diagram = change in V
- Area under V diagram = change in M
Bending Stress
For a beam in pure bending:
σ = -M × y / I
where:
- M = bending moment
- y = distance from the neutral axis
- I = moment of inertia of the cross-section
Maximum stress occurs at the outermost fibers (y = c):
σ_max = M × c / I
Define section modulus S = I / c. Then:
σ_max = M / S
Moments of Inertia
For a rectangular cross-section b × h:
I = b × h³ / 12
For a circular section of diameter d:
I = π × d⁴ / 64
For a hollow circle:
I = π × (d_o⁴ - d_i⁴) / 64
The I-beam shape concentrates material far from the neutral axis, maximizing I for a given mass.
Deflection of Beams
The beam equation:
EI × d²y/dx² = M(x)
Integrating twice gives deflection y(x). Boundary conditions fix the constants.
For a simply supported beam with a point load P at the center:
δ_max = P × L³ / (48 × E × I)
For a cantilever with point load P at the tip:
δ_max = P × L³ / (3 × E × I)
For a uniformly loaded simple beam (total load W):
δ_max = 5 × W × L³ / (384 × E × I)
These formulas are in every engineering handbook.
Beam Design
The goal: choose a cross-section that satisfies both strength and stiffness.
Strength: σ_max ≤ σ_allow → S ≥ M / σ_allow
Stiffness: δ_max ≤ δ_allow → I ≥ f(M, L, δ_allow)
Usually stiffness governs for long spans. That's why large deflection limits (L/360 for floors, L/500 for precision) drive beam sizes.
Shear Stress in Beams
τ = V × Q / (I × t)
where Q is the first moment of area above the point, and t is the thickness at that point.
For a rectangular section, τ is parabolic, peaking at the neutral axis:
τ_max = 3V / (2A)
For an I-beam, τ_max is at the neutral axis, in the web.
Composite Beams
When a beam is made of two materials (e.g., steel and concrete), transform one material into an equivalent section of the other using the modular ratio n = E₂/E₁.
Key Takeaways
- dV/dx = -w, dM/dx = V
- Bending stress: σ = Mc/I, max at outer fibers
- Deflection formulas are ready-made for common cases
- I-beam shape maximizes I for mass
- Shear stress: τ = VQ/(It)
- Composite beams need the modular ratio
Column Buckling and Stability
Buckling — The Sudden Failure A slender column under compression can fail suddenly by buckling — sideways deflection — at a load far below the material's yield strength. This is why a plastic...
Buckling — The Sudden Failure
A slender column under compression can fail suddenly by buckling — sideways deflection — at a load far below the material's yield strength. This is why a plastic ruler can carry tension but buckles easily in compression.
Euler's Buckling Formula
For a pin-ended column of length L, the critical buckling load is:
P_cr = π² × E × I / L²
where:
- E = Young's modulus
- I = minimum moment of inertia
- L = effective length (see below)
This is the Euler buckling load. Above P_cr, the column is unstable; below it, it's stable.
Effective Length
Real columns have different end conditions. The effective length L_e accounts for this:
| End condition | L_e |
|---------------|-----|
| Pinned-pinned | L |
| Fixed-fixed | 0.5L |
| Fixed-pinned | 0.7L |
| Fixed-free (cantilever) | 2L |
So P_cr for a cantilever is only 1/4 of the pin-ended value. Fixing the base helps a lot.
Critical Stress
σ_cr = P_cr / A = π² × E / (L_e/r)²
where r = √(I/A) is the radius of gyration. The ratio L_e/r is the slenderness ratio.
For steel with E = 200 GPa:
- L/r = 100 → σ_cr = 200 MPa (near yield)
- L/r = 200 → σ_cr = 50 MPa (well below yield)
Buckling governs for slender columns (L/r > ~100 for steel).
When Buckling Doesn't Apply
If σ_cr > σ_y, the column yields before buckling. Then the column fails by yielding, not buckling. Use yield criteria.
The transition slenderness ratio:
(L/r)_transition = π × √(E / σ_y)
For steel (E = 200 GPa, σ_y = 250 MPa):
(L/r)_transition = π × √(200,000/250) = π × 28.3 = 89
So for L/r < 89, yielding governs. For L/r > 89, buckling governs.
Real Columns: Initial Imperfections
Real columns are never perfectly straight. Initial crookedness and eccentric loads reduce the buckling load.
The Johnson parabola and other empirical formulas account for this. Real design codes (AISC, Eurocode) use semi-empirical curves calibrated to test data.
Rankine-Gordon Formula
A useful interpolation between yielding and Euler:
P_cr = P_yield × P_euler / (P_yield + P_euler)
This smoothly transitions between the two regimes.
Other Buckling Modes
- Local buckling: thin-walled sections buckle locally (e.g., the flange of an I-beam)
- Torsional buckling: columns with asymmetric cross-sections can twist
- Lateral-torsional buckling: beams loaded in bending can buckle sideways
Each has its own critical load formula.
Design Implications
For a column:
- Compute L/r and P_cr
- Check P_cr > applied load with safety factor
- If slender, increase I (use a hollow or I-shaped section)
- If short, check yielding
For very slender structures (towers, drill strings, space frames), buckling is often the governing failure mode.
Key Takeaways
- Buckling is sudden instability under compression
- Euler formula: P_cr = π²EI/L²
- Effective length depends on end conditions
- Slenderness ratio L/r determines if buckling or yielding governs
- Real columns have reduced capacity due to imperfections
- Hollow and I-sections are efficient against buckling
- Buckling governs for slender structures
Failure Theories and Fatigue
Failure — What Does It Mean? Failure can be: Yielding: permanent deformation Fracture: sudden breaking Buckling: instability Fatigue: failure after many cycles Different materials f...
Failure — What Does It Mean?
Failure can be:
- Yielding: permanent deformation
- Fracture: sudden breaking
- Buckling: instability
- Fatigue: failure after many cycles
Different materials fail differently. Ductile materials (steel, aluminum) yield and then fracture. Brittle materials (cast iron, ceramics, glass) fracture without warning.
Ductile vs Brittle
Ductile:
- Large plastic deformation before fracture
- Warning signs (yielding, necking)
- Examples: mild steel, aluminum, copper
Brittle:
- Little to no plastic deformation
- Sudden fracture
- Examples: cast iron, glass, ceramics, high-strength steel at low temperature
Fracture mechanics handles brittle failure; mechanics of materials handles ductile failure.
Yield Criteria for Ductile Materials
Under multiaxial stress, when does yielding occur?
Tresca (Maximum Shear Stress): yielding when maximum shear stress equals half the yield strength:
τ_max = σ_y / 2
Conservative; matches experiments for many ductile metals.
von Mises (Maximum Distortion Energy): yielding when the distortion energy equals the yield strength in uniaxial tension:
σ_vm = √(σ₁² - σ₁σ₂ + σ₂² - σ₂σ₃ + σ₃σ₁) = σ_y
More accurate for most ductile metals. Standard in FEA software.
For a simple uniaxial tension test, both criteria reduce to σ = σ_y.
Fracture Criteria for Brittle Materials
Maximum Normal Stress: fracture when the largest principal stress reaches the ultimate tensile strength.
Used for cast iron, ceramics, and other brittle materials. Does not depend on shear.
Fatigue — The Silent Killer
Fatigue is failure under repeated cyclic loading at stress levels far below yield. A paperclip bent back and forth 20 times breaks — not because of a single high load, but because of accumulated microcracks.
Fatigue causes ~90% of all service failures in metals. Bridges, aircraft, machine parts, medical implants.
S-N Curve
Fatigue testing produces an S-N curve: stress amplitude S vs number of cycles to failure N.
For steel, the curve has a fatigue limit (endurance limit) — below this stress, the material survives indefinitely. Typical: 0.4-0.5 × ultimate tensile strength.
For aluminum and most other metals, no fatigue limit — the S-N curve keeps decreasing. Design is based on a specified life (e.g., 10⁷ cycles).
Fatigue Life Prediction
Basquin's equation:
σ_a = σ_f' × (2N_f)^b
where σ_f' is the fatigue strength coefficient and b is the fatigue strength exponent (typically -0.05 to -0.12).
Miner's rule for variable amplitude:
Σ (n_i / N_i) = 1
Accumulate damage until the sum reaches 1 (failure).
Stress Concentrations and Fatigue
Notches and holes concentrate stress, dramatically reducing fatigue life. The fatigue notch factor K_f:
K_f = 1 + q × (K_t - 1)
where q is the notch sensitivity (0 to 1) and K_t is the elastic stress concentration factor.
Design: round all corners, avoid sharp changes in section, polish surfaces in high-stress regions.
Surface Effects
Fatigue cracks start at the surface. Surface treatments improve fatigue life:
- Shot peening: compresses the surface, adds residual compressive stress
- Carburizing: hardens the surface
- Polishing: removes stress-raisers
- Coating: protects from corrosion
Surface finish can change fatigue life by 2-3×.
Design for Fatigue
- Keep stress amplitudes below the fatigue limit (if applicable)
- Avoid sharp changes in section
- Use smooth surface finishes
- Apply compressive residual stress (shot peening)
- Account for stress concentrations
- Test prototypes
Key Takeaways
- Ductile materials yield; brittle materials fracture
- von Mises is the standard yield criterion
- Fatigue is failure under cyclic loading, below yield
- Steel has an endurance limit; aluminum does not
- Notches and surface finish strongly affect fatigue
- Miner's rule for variable-amplitude loading
- Design for fatigue is critical for safety
📝 Problem Set 1: Stress, Strain, Bending
Q1. A steel rod 2m long with cross-section 100 mm² carries 20 kN. If E = 200 GPa, find stress and elongation.
Show Solution
σ = 20000/100e-6 = 200 MPa. δ = 20000 × 2 / (100e-6 × 200e9) = 40000 / (2e7) = 2 mm.
Q2. A simply supported beam of length 4 m carries a 10 kN point load at midspan. Max moment? Max deflection? (E = 200 GPa, I = 50×10⁶ mm⁴)
Show Solution
M_max = 10,000 × 4 / 4 = 10 kN·m. δ = 10,000 × 4³ / (48 × 200e9 × 50e-6) = 640,000 / (480e6) = 1.33 mm.
Q3. A solid shaft of diameter 50 mm transmits 100 kW at 1500 rpm. Find the maximum shear stress.
Show Solution
ω = 2π × 1500/60 = 157 rad/s. T = 100000/157 = 637 N·m. τ = 16 × 637 / (π × 0.05³) = 10192 / 0.0003927 = 25.9 MPa.
🎯 Midterm 1: Stress, Bending, Torsion, Buckling
Q1. For a cantilever beam 3 m long with distributed load w = 5 kN/m, find the maximum bending moment and deflection (E = 200 GPa, I = 100×10⁶ mm⁴).
Show Solution
M_max = wL²/2 = 5000 × 9 / 2 = 22.5 kN·m. δ = wL⁴/(8EI) = 5000 × 81 / (8 × 200e9 × 100e-6) = 405,000 / (160e6) = 2.53 mm.
Q2. A hollow shaft has outer diameter 100 mm, inner 70 mm. What is the polar moment of inertia?
Show Solution
J = π(d_o⁴ - d_i⁴)/32 = π(0.1⁴ - 0.07⁴)/32 = π(0.0001 - 0.00002401)/32 = π × 0.00007599/32 = 7.46e-6 m⁴.
Q3. A 3 m steel column is pinned at both ends with square cross-section 50×50 mm. Find the buckling load (E = 200 GPa).
Show Solution
I = b⁴/12 = 0.05⁴/12 = 5.2e-7 m⁴. P_cr = π²EI/L² = π² × 200e9 × 5.2e-7 / 3² = 1.03e6/9 = 114 kN. Now check: σ_cr = P_cr/A = 114000/0.0025 = 45.6 MPa < yield (250 MPa) → buckling governs.