Reference topics: MIT 2.51 · independent study notes, not affiliated

Heat Transfer

Conduction, convection, radiation, and heat exchanger design.

5Lectures
1Assignments
1Exams
38hDuration
1

Introduction to Heat Transfer Modes

What is Heat Transfer? Heat transfer is the study of energy movement due to temperature differences. It's distinct from thermodynamics: thermodynamics tells us whether a process is possible; heat...

⏱ 50 min read

What is Heat Transfer?

Heat transfer is the study of energy movement due to temperature differences. It's distinct from thermodynamics: thermodynamics tells us whether a process is possible; heat transfer tells us how fast it happens.

Three modes:

  1. Conduction: through solids or stationary fluids
  2. Convection: between a surface and a moving fluid
  3. Radiation: electromagnetic waves, no medium needed

Conduction — Fourier's Law

q = -k × A × dT/dx

where q is the heat rate (W), k is thermal conductivity (W/m·K), A is area (m²), and dT/dx is the temperature gradient.

For a plane wall of thickness L:

q = k × A × (T₁ - T₂) / L

Thermal resistance:

R_cond = L / (k × A)

Thermal Conductivity

| Material | k (W/m·K) |
|----------|-----------|
| Air | 0.026 |
| Foam | 0.03 |
| Water | 0.6 |
| Glass | 1.0 |
| Stainless steel | 16 |
| Aluminum | 205 |
| Copper | 385 |
| Diamond | 2000 |

The huge range (5 orders of magnitude) explains why insulation works so well and why heat sinks are made of aluminum or copper.

Convection — Newton's Law of Cooling

q = h × A × (T_s - T_∞)

where h is the convection heat transfer coefficient (W/m²·K):

  • Natural convection (air): 5-25
  • Forced convection (air): 25-250
  • Natural convection (water): 20-100
  • Forced convection (water): 500-10,000
  • Boiling: 3,000-100,000
  • Condensation: 5,000-100,000

Convective thermal resistance:

R_conv = 1 / (h × A)

Radiation — Stefan-Boltzmann

q = ε × σ × A × (T_s⁴ - T_surr⁴)

where ε is emissivity (0-1), σ = 5.67 × 10⁻⁸ W/m²·K⁴.

For small temperature differences, we can linearize:

q ≈ h_r × A × (T_s - T_surr)

where h_r = 4εσT_m³ is the radiative heat transfer coefficient.

At room temperature, h_r ≈ 6 W/m²·K for ε = 1. So radiation is comparable to natural convection at room temperature.

Combined Heat Transfer

Real systems often have all three modes simultaneously. Use thermal resistance networks:

R_total = R_conv1 + R_cond + R_conv2

For a composite wall with N layers:

R_total = Σ (L_i / k_i A) + 1/(h₁A) + 1/(h₂A)

Heat rate:

q = ΔT / R_total

Overall Heat Transfer Coefficient

For a wall separating two fluids:

q = U × A × ΔT

where U is the overall coefficient:

1/U = 1/h₁ + Σ(L_i/k_i) + 1/h₂

U values:

  • Single glass window: U = 5.7 W/m²·K
  • Double glazed: U = 2.8 W/m²·K
  • Well-insulated wall: U = 0.3 W/m²·K
  • Vacuum flask: U < 0.05

Key Takeaways

  • Three modes: conduction, convection, radiation
  • Fourier: q = -kA dT/dx
  • Newton: q = hA(T_s - T_∞)
  • Stefan-Boltzmann: q = εσA(T_s⁴ - T_surr⁴)
  • Thermal resistance networks combine modes
  • U-value summarizes overall heat transfer
2

Steady-State Conduction

The Heat Diffusion Equation The general equation for conduction: ∂/∂x (k ∂T/∂x) + ∂/∂y (k ∂T/∂y) + ∂/∂z (k ∂T/∂z) + q_gen = ρ Cp ∂T/∂t For 1D, steady, no generation: d/dx (k dT/dx) = 0 For con...

⏱ 50 min read

The Heat Diffusion Equation

The general equation for conduction:

∂/∂x (k ∂T/∂x) + ∂/∂y (k ∂T/∂y) + ∂/∂z (k ∂T/∂z) + q_gen = ρ Cp ∂T/∂t

For 1D, steady, no generation:

d/dx (k dT/dx) = 0

For constant k:

d²T/dx² = 0

Solution: T(x) is linear in a plane wall.

Plane Wall

Temperature profile: T(x) = T₁ + (T₂ - T₁) × x/L

Heat rate: q = kA(T₁ - T₂)/L

Constant heat rate through the wall.

Cylindrical Wall (Pipe Insulation)

For a cylinder of inner radius r₁ and outer radius r₂:

q = 2πkL(T₁ - T₂) / ln(r₂/r₁)

Thermal resistance:

R = ln(r₂/r₁) / (2πkL)

The critical radius of insulation:

r_cr = k / h

Adding insulation increases heat loss until r = r_cr, then decreases. For thin wires, adding a small amount of insulation can actually increase heat loss.

Spherical Shell

q = 4πk(T₁ - T₂) / (1/r₁ - 1/r₂)

Used for spherical tanks and spheres of insulating material.

Composite Walls

For N layers in series:

q = (T₁ - T_{N+1}) / Σ R_i

where R_i = L_i / (k_i A).

Interface temperatures are found by working through the resistances.

Contact Resistance

Real surfaces have microscopic roughness, creating an interface resistance:

R_contact = 1 / (h_c A)

where h_c is the contact conductance (W/m²·K). Typical values:

  • Metal-metal, smooth, high pressure: 10,000-30,000
  • Metal-metal, rough, low pressure: 1,000-5,000
  • With thermal paste: 5,000-20,000
  • With air gap: 100-1,000

This matters for electronics cooling — a bad CPU-heatsink interface can dominate thermal resistance.

Extended Surfaces (Fins)

Fins increase surface area for convective heat transfer. Common types:

  • Straight fins (rectangular cross-section)
  • Pin fins (circular)
  • Annular fins (around pipes)

Fin efficiency:

η_fin = actual heat transfer / maximum possible (if entire fin at base temperature)

For a straight fin with adiabatic tip:

η_fin = tanh(mL) / (mL)

where m = √(hP/(kA_c)).

Overall surface efficiency:

η_o = 1 - (A_fin/A_total) × (1 - η_fin)

Fin effectiveness:

ε_fin = q_fin / (h A_c θ_b)

Effective fins have ε > 2. For ε < 2, the fin isn't worth the cost.

Applications

  • Heat sinks for electronics (aluminum fins)
  • Radiators in cars
  • Fins on air-cooled engines
  • Heat exchanger tubes (often finned on the air side)

Key Takeaways

  • 1D steady conduction: T is linear in a plane wall, logarithmic in a cylinder
  • Composite walls: resistances add
  • Contact resistance is often the bottleneck
  • Fins increase surface area; efficiency depends on geometry
  • Critical radius of insulation for cylinders
  • Fin effectiveness must exceed 2 for a fin to be worthwhile
3

Convection Fundamentals

The Convection Coefficient Convection depends on: Fluid properties (k, μ, Cp, ρ) Flow velocity Surface geometry Whether flow is laminar or turbulent Whether it&#39;s natural or forced The...

⏱ 50 min read

The Convection Coefficient

Convection depends on:

  • Fluid properties (k, μ, Cp, ρ)
  • Flow velocity
  • Surface geometry
  • Whether flow is laminar or turbulent
  • Whether it's natural or forced

The convection coefficient h bundles all of this. Typical values range from 5 to 100,000 W/m²·K — a huge range.

The Nusselt Number

Dimensionless heat transfer coefficient:

Nu = h × L / k_fluid

Nu = 1 means pure conduction; Nu >> 1 means convection dominates.

For a flat plate in laminar flow:

Nu = 0.332 × Re^0.5 × Pr^(1/3)

For turbulent:

Nu = 0.037 × Re^0.8 × Pr^(1/3)

Reynolds and Prandtl Numbers

Re = ρVL/μ characterizes flow regime.

Pr = μCp/k = ν/α characterizes the fluid:

  • Liquid metals: Pr << 1
  • Gases: Pr ≈ 0.7
  • Water: Pr ≈ 7
  • Oils: Pr >> 100

External Flow over a Flat Plate

Laminar boundary layer until Re_x = 5 × 10⁵. Then transition to turbulent.

Local Nusselt number:
Laminar: Nu_x = 0.332 Re_x^0.5 Pr^(1/3)
Turbulent: Nu_x = 0.0296 Re_x^0.8 Pr^(1/3)

Average Nusselt number over a plate of length L:
Laminar: Nu_L = 0.664 Re_L^0.5 Pr^(1/3)
Turbulent: Nu_L = 0.037 Re_L^0.8 Pr^(1/3)

Flow over Cylinders and Spheres

The Churchill-Bernstein correlation covers a wide Re range for cylinders:

Nu_D = 0.3 + 0.62 Re^0.5 Pr^(1/3) / [1 + (0.4/Pr)^(2/3)]^0.25 × [1 + (Re/282000)^0.625]^0.8

For spheres, the Whitaker correlation is standard.

Internal Flow (Pipe Flow)

Entry length: L_e/D ≈ 0.05 Re (laminar), 10 (turbulent).

For laminar fully developed flow:
Nu_D = 3.66 (constant wall temperature)
Nu_D = 4.36 (constant heat flux)

For turbulent (Dittus-Boelter):
Nu_D = 0.023 Re^0.8 Pr^n
where n = 0.4 for heating, 0.3 for cooling

Natural Convection

When buoyancy drives flow, use:

Nu = C × Ra^n

where Ra = Gr × Pr is the Rayleigh number:

Gr = g β ΔT L³ / ν² (Grashof number)

Typical for a vertical plate:
Laminar (10⁴ < Ra < 10⁹): Nu = 0.59 Ra^0.25
Turbulent (Ra > 10⁹): Nu = 0.13 Ra^(1/3)

Natural convection gives much lower h than forced. Air-cooled heat sinks rely on natural convection, so they need to be large.

Boiling and Condensation

Boiling has different regimes:

  • Nucleate boiling: bubbles form at nucleation sites, very high h
  • Transition boiling: unstable, h decreases
  • Film boiling: vapor blanket, low h (this is why quenching in water works — the film boiling phase cools slowly)

Condensation:

  • Filmwise: liquid film on surface, moderate h
  • Dropwise: droplets form and fall off, much higher h (10× filmwise)

Key Takeaways

  • Convection coefficient h is the key unknown
  • Nusselt number relates h to k
  • Correlations exist for common geometries
  • Laminar vs turbulent matters (different Nu formulas)
  • Natural convection gives lower h than forced
  • Boiling and condensation have extremely high h
  • Always check which correlation applies to your case
4

Radiation Heat Transfer

The Nature of Radiation All objects emit electromagnetic radiation. The intensity and spectrum depend on temperature. Thermal radiation is in the infrared (wavelength 0.1-100 µm) for room-temperature...

⏱ 50 min read

The Nature of Radiation

All objects emit electromagnetic radiation. The intensity and spectrum depend on temperature.

Thermal radiation is in the infrared (wavelength 0.1-100 µm) for room-temperature objects, and extends into visible for very hot objects (like the sun).

Blackbody Radiation

A blackbody absorbs all incident radiation. Its emission is described by:

Planck's law (spectral distribution):

E_λb = (2πhc² / λ⁵) × 1 / (e^(hc/λkT) - 1)

Wien's displacement law (peak wavelength):

λ_max = 2898 / T (µm, with T in K)

At T = 3000 K, λ_max = 0.97 µm (infrared, near-visible).

Stefan-Boltzmann law (total emission):

E_b = σ T⁴

where σ = 5.67 × 10⁻⁸ W/m²·K⁴.

Real Surfaces

Real surfaces emit less than a blackbody. The ratio is emissivity ε:

E = ε × σ × T⁴

Emissivity ranges:

  • Polished aluminum: ε = 0.05
  • Oxidized aluminum: ε = 0.3
  • White paint: ε = 0.9
  • Black paint: ε = 0.95
  • Human skin: ε = 0.98

High-emissivity surfaces radiate well; low-emissivity surfaces (like polished metal) do not. This is why silvered surfaces are used in vacuum flasks.

Absorptivity, Reflectivity, Transmissivity

Incident radiation is distributed among:

  • Absorptivity α (absorbed)
  • Reflectivity ρ (reflected)
  • Transmissivity τ (transmitted)

α + ρ + τ = 1

For opaque surfaces, τ = 0, so α + ρ = 1.

Kirchhoff's law: for a surface in thermal equilibrium, α = ε at each wavelength. Good absorbers are good emitters.

View Factors

Radiative exchange between surfaces depends on geometry through the view factor F_ij — the fraction of radiation leaving surface i that reaches surface j.

Reciprocity: A_i F_ij = A_j F_ji

Summation: Σ F_ij = 1

For common geometries, F values are tabulated:

  • Two parallel plates: F = 1 for infinite plates
  • Small object in large enclosure: F = 1 (all emission reaches enclosure)
  • Two perpendicular plates: F ≈ 0.2

Radiation Exchange Between Surfaces

For two gray diffuse surfaces forming an enclosure:

q_12 = σ × (T₁⁴ - T₂⁴) / [(1-ε₁)/(ε₁A₁) + 1/(A₁F₁₂) + (1-ε₂)/(ε₂A₂)]

This is the general formula. For common cases, simplifications exist:

Small object in large enclosure:

q = ε × σ × A × (T_s⁴ - T_surr⁴)

Combined Convection and Radiation

Real surfaces lose heat by both convection and radiation. Add the two:

q_total = h_conv × A × (T_s - T_air) + ε × σ × A × (T_s⁴ - T_surr⁴)

For small ΔT, linearize radiation:

h_r = 4 × ε × σ × T_m³

So total h = h_conv + h_r. At room temperature, h_r ≈ 6 W/m²·K for ε = 1.

Radiation Shields

To reduce radiation, insert a low-emissivity shield between surfaces. Each shield reduces heat transfer.

For N shields between two surfaces:

q_with_shields / q_without = 1 / (N + 1)

This is how multi-layer insulation (MLI) works in spacecraft — many aluminized Mylar layers reduce radiative heat loss dramatically.

Key Takeaways

  • All objects radiate; blackbodies are ideal emitters
  • Stefan-Boltzmann: E = εσT⁴
  • Wien's law: peak wavelength = 2898/T
  • Kirchhoff: α = ε (good absorbers are good emitters)
  • View factors describe geometric exchange
  • Radiation shields reduce heat transfer
  • At room temperature, radiation ≈ convection (h_r ≈ 6)
  • At high temperature, radiation dominates (T⁴)
5

Heat Exchangers

What is a Heat Exchanger? A device that transfers heat between two fluids without mixing them. Everywhere: Car radiators Air conditioners Power plant condensers Chemical plant preheaters Computer C...

⏱ 50 min read

What is a Heat Exchanger?

A device that transfers heat between two fluids without mixing them. Everywhere:

  • Car radiators
  • Air conditioners
  • Power plant condensers
  • Chemical plant preheaters
  • Computer CPU coolers
  • Refrigerators

Classification

By flow arrangement:

  • Parallel flow: both fluids enter at the same end, flow in the same direction
  • Counterflow: fluids enter at opposite ends, flow in opposite directions
  • Crossflow: fluids flow perpendicular to each other
  • Shell and tube: one fluid in tubes, one in the shell

By construction:

  • Tubular: concentric tubes, shell-and-tube, spiral
  • Plate: flat plates stacked, compact
  • Extended surface: finned tubes (for gas-liquid)

The Overall Heat Transfer Coefficient

Q = U × A × ΔT_lm

where:

  • Q = heat duty (W)
  • U = overall heat transfer coefficient
  • A = heat transfer area
  • ΔT_lm = log mean temperature difference

U depends on the individual resistances:

1/UA = 1/(h_i A_i) + R_wall + 1/(h_o A_o)

where i and o refer to inner and outer surfaces.

Typical U values:

  • Water-to-water: 800-1500 W/m²·K
  • Water-to-air (finned): 25-100
  • Steam-to-water: 1000-3000
  • Gas-to-gas: 10-50

Log Mean Temperature Difference

For counterflow or parallel flow:

ΔT_lm = (ΔT₁ - ΔT₂) / ln(ΔT₁/ΔT₂)

where ΔT₁ and ΔT₂ are the temperature differences at the two ends.

Counterflow gives higher ΔT_lm than parallel flow for the same inlet/outlet temperatures → smaller heat exchanger for the same duty.

Counterflow vs Parallel

Consider hot fluid cooling from 100°C to 60°C, cold fluid heating from 20°C to 50°C.

Parallel flow:

  • ΔT₁ = 100 - 20 = 80°C
  • ΔT₂ = 60 - 50 = 10°C
  • ΔT_lm = (80-10)/ln(8) = 43.3°C

Counterflow:

  • ΔT₁ = 100 - 50 = 50°C
  • ΔT₂ = 60 - 20 = 40°C
  • ΔT_lm = (50-40)/ln(1.25) = 44.8°C

Similar in this case, but counterflow can achieve much more when the hot outlet would be lower than the cold outlet.

Effectiveness-NTU Method

When outlet temperatures are unknown (they depend on the heat exchanger), the LMTD method requires iteration. The effectiveness-NTU method avoids this.

Effectiveness (ε):

ε = Q_actual / Q_max

where Q_max = C_min × (T_h,in - T_c,in).

C_min is the smaller of C_h = m_h × Cp_h and C_c = m_c × Cp_c.

NTU (Number of Transfer Units):

NTU = U × A / C_min

For each flow arrangement, there's a relation between ε and NTU:

Parallel flow:
ε = [1 - exp(-NTU(1 + Cr))] / (1 + Cr)

Counterflow:
ε = [1 - exp(-NTU(1 - Cr))] / [1 - Cr × exp(-NTU(1 - Cr))]

where Cr = C_min / C_max.

For Cr = 1 counterflow: ε = NTU / (1 + NTU).

Design Procedure

  1. Compute heat duty Q = m_h × Cp_h × (T_h,in - T_h,out)
  2. Compute C_min, C_max, Cr
  3. Compute Q_max = C_min × (T_h,in - T_c,in)
  4. Required ε = Q / Q_max
  5. From ε-NTU relation, find NTU
  6. A = NTU × C_min / U

Fouling

Over time, deposits on heat transfer surfaces add resistance. Fouling factors R_f are added to the U calculation:

1/U_dirty = 1/U_clean + R_f,i + R_f,o

Typical fouling factors: 0.0001-0.001 m²·K/W.

Fouling is often the dominant resistance after months of operation. Regular cleaning (chemical or mechanical) is essential.

Key Takeaways

  • Heat exchangers transfer heat between fluids
  • Counterflow is more efficient than parallel flow
  • LMTD method: Q = UA ΔT_lm
  • ε-NTU method when outlet temps are unknown
  • U depends on both fluid-side resistances
  • Fouling adds resistance over time
  • Compact heat exchangers use fins for gas-side enhancement

📝 Problem Set 1: Conduction, Convection, Radiation

Q1. A wall 0.2 m thick with k = 0.8 W/m·K has inner surface at 25°C and outer at 5°C. Find heat flux.

Show Solution

q/A = kΔT/L = 0.8 × 20 / 0.2 = 80 W/m².

Q2. A surface at 100°C loses heat by natural convection to air at 20°C (h = 10 W/m²·K) and radiation (ε = 0.9). Find total heat flux.

Show Solution

q_conv = 10 × 80 = 800 W/m². q_rad = 0.9 × 5.67e-8 × (373⁴ - 293⁴) = 0.9 × 5.67e-8 × (1.936e10 - 7.37e9) = 0.9 × 5.67e-8 × 1.199e10 = 612 W/m². Total = 1412 W/m².

Q3. A fin has efficiency 0.7 and area 0.01 m². Base is at 80°C, ambient 25°C, h = 20 W/m²·K. Find heat transfer from the fin.

Show Solution

q = 0.7 × 20 × 0.01 × 55 = 7.7 W.

🎯 Midterm 1: Conduction, Convection, Radiation, HX

Q1. A composite wall has two layers: 5 cm of brick (k=0.7) and 10 cm of insulation (k=0.04). Total ΔT = 30°C over 1 m². Find the heat rate.

Show Solution

R_brick = 0.05/0.7 = 0.0714 K/W. R_insul = 0.1/0.04 = 2.5 K/W. R_total = 2.571 K/W. q = 30/2.571 = 11.7 W.

Q2. A CPU dissipates 65 W. Heatsink has R_sa = 0.3 K/W, paste R_cs = 0.1 K/W. Ambient 25°C. Find the CPU case temperature.

Show Solution

T_case = 25 + 65 × (0.3 + 0.1) = 25 + 26 = 51°C.

Q3. A counterflow heat exchanger has U = 500 W/m²·K, A = 2 m². Hot fluid: 90°C in, 60°C out. Cold: 20°C in, 40°C out. Find heat duty.

Show Solution

ΔT1 = 90-40 = 50. ΔT2 = 60-20 = 40. LMTD = (50-40)/ln(50/40) = 10/0.223 = 44.8°C. Q = 500 × 2 × 44.8 = 44,800 W = 44.8 kW.