Reference topics: MIT 2.06 · independent study notes, not affiliated

Fluid Mechanics

Fluid statics, Bernoulli, Navier-Stokes, boundary layers, and turbulence.

5Lectures
1Assignments
1Exams
40hDuration
1

Fluid Properties and Hydrostatics

What is a Fluid? A fluid is a substance that deforms continuously under shear stress, no matter how small. Gases and liquids are fluids; solids are not. This distinction matters because fluids flow,...

⏱ 50 min read

What is a Fluid?

A fluid is a substance that deforms continuously under shear stress, no matter how small. Gases and liquids are fluids; solids are not. This distinction matters because fluids flow, and their behavior is governed by different equations than solids.

Key Fluid Properties

Density (ρ): mass per unit volume. Water: 1000 kg/m³, air at sea level: 1.2 kg/m³.

Specific weight (γ): weight per unit volume. γ = ρg.

Viscosity (μ): resistance to shear. Water at 20°C: 0.001 Pa·s. Honey: 10 Pa·s.

Kinematic viscosity (ν): ν = μ/ρ. Water: 10⁻⁶ m²/s. Important in boundary layer analysis.

Surface tension (σ): energy per unit area at a liquid-gas interface. Water-air: 0.072 N/m. Explains capillary action, droplet formation, and why insects can walk on water.

Bulk modulus (K): resistance to compression. Water: 2.2 GPa. Liquids are almost incompressible, which is why hydraulic systems work.

Pressure

Pressure is force per unit area:

P = F/A

Units: pascal (Pa), bar (10⁵ Pa), atmosphere (101,325 Pa), psi (6895 Pa).

Absolute vs gauge pressure: absolute pressure is measured from vacuum; gauge pressure is measured relative to atmospheric:

P_abs = P_gauge + P_atm

Most pressure gauges read gauge pressure.

Hydrostatic Pressure

Pressure in a static fluid increases with depth:

P = P₀ + ρ × g × h

For water, each 10 m of depth adds ~1 atm of pressure.

This is why:

  • Submarines have thick hulls
  • Dams are thicker at the base
  • Ears hurt at the bottom of a pool

Hydrostatic Force on a Surface

For a submerged flat plate:

F = ρ × g × h_c × A

where h_c is the depth of the centroid and A is the area.

The center of pressure (where the resultant force acts) is always below the centroid for a vertical surface, because pressure increases with depth.

y_cp = y_c + I_c / (y_c × A)

where I_c is the moment of inertia about the centroidal axis.

Buoyancy — Archimedes' Principle

A body immersed in a fluid experiences an upward buoyant force equal to the weight of the displaced fluid:

F_b = ρ_fluid × g × V_displaced

If F_b > weight, the body floats. If F_b < weight, it sinks.

A floating body displaces a volume of fluid equal to its weight. This is how ships float, how hot air balloons rise, and how fish control depth with their swim bladders.

Stability of Floating Bodies

A floating body is stable if, when tilted, the restoring moment brings it back upright. The key point is the metacenter — the intersection of the buoyancy force line with the body's axis.

  • If metacenter is above center of gravity: stable
  • If metacenter is below center of gravity: unstable

This is why ships carry ballast low in the hull — to keep the center of gravity low.

Manometry

Manometers measure pressure using columns of liquid:

P₁ - P₂ = ρ × g × Δh

U-tube manometers are the classic instrument. Inclined manometers amplify the reading for small pressure differences.

Key Takeaways

  • Fluids deform continuously under shear
  • Hydrostatic pressure: P = ρgh
  • Buoyancy: F = ρ_fluid × g × V_displaced
  • Metacenter determines stability of floating bodies
  • Manometers measure pressure via liquid columns
  • Viscosity, surface tension, and bulk modulus are the key fluid properties
2

Fluid Kinematics and Bernoulli Equation

Describing Fluid Motion Two frameworks: Lagrangian: follow individual particles. Good for tracking. Eulerian: observe what happens at fixed points. Standard in fluid mechanics. In the Eulerian vi...

⏱ 50 min read

Describing Fluid Motion

Two frameworks:

Lagrangian: follow individual particles. Good for tracking.

Eulerian: observe what happens at fixed points. Standard in fluid mechanics.

In the Eulerian view, velocity is a field v(x, y, z, t).

Types of Flow

  • Steady: properties don't change with time at any point
  • Unsteady: properties change with time
  • Laminar: smooth, orderly, parallel streamlines
  • Turbulent: chaotic, with random fluctuations
  • Incompressible: density is constant (liquids and low-speed gases)
  • Inviscid: viscosity is negligible
  • 1D, 2D, 3D: number of spatial dimensions needed

Streamlines, Pathlines, Streaklines

  • Streamline: curve tangent to velocity at every point (instantaneous)
  • Pathline: trajectory of a single particle over time
  • Streakline: locus of particles that passed a given point

In steady flow, all three coincide.

Continuity Equation

Mass conservation:

ρ₁ A₁ V₁ = ρ₂ A₂ V₂

For incompressible flow:

A₁ V₁ = A₂ V₂

Flow rate Q = A × V is constant. A wide pipe has slow flow; a narrow pipe has fast flow.

The Bernoulli Equation

For steady, incompressible, inviscid flow along a streamline:

P + ½ ρ V² + ρ g z = constant

Each term is energy per unit volume:

  • P: pressure energy (static pressure)
  • ½ρV²: kinetic energy (dynamic pressure)
  • ρgz: potential energy (hydrostatic)

The Bernoulli equation is the most-used equation in fluid mechanics.

Applications of Bernoulli

Pitot tube: measures velocity from stagnation pressure.

V = √(2 × (P_stagnation - P_static) / ρ)

Used on aircraft (airspeed indicator) and in wind tunnels.

Venturi meter: narrow section speeds up flow, drops pressure; measure ΔP to find Q.

Atomizer: fast air past a liquid surface creates low pressure that sucks liquid up and disperses it.

Airfoil: faster air over the top of the wing = lower pressure = lift.

Curveball: spinning ball drags air, creating asymmetric pressure → sideways force.

Limitations of Bernoulli

Bernoulli assumes:

  • Steady flow
  • Incompressible
  • Inviscid (no friction)
  • Along a streamline

Real flows have viscosity, which causes energy losses. The extended Bernoulli with head loss:

P₁/ρg + V₁²/2g + z₁ = P₂/ρg + V₂²/2g + z₂ + h_L

where h_L is the head loss (energy lost to friction).

Energy Line and Hydraulic Grade Line

Energy Line (EL): total energy = P/ρg + V²/2g + z. Always decreasing in real flow.

Hydraulic Grade Line (HGL): piezometric head = P/ρg + z. The HGL is always below the EL by V²/2g.

These lines are used in pipe network analysis to visualize pressure distribution.

Key Takeaways

  • Eulerian viewpoint describes velocity fields
  • Laminar vs turbulent, steady vs unsteady
  • Continuity: A₁V₁ = A₂V₂
  • Bernoulli: P + ½ρV² + ρgz = constant
  • Applies only to steady, inviscid, incompressible flow
  • Pitot, Venturi, airfoil all use Bernoulli
  • Real flows have losses — extended Bernoulli includes h_L
3

Viscous Flow and the Navier-Stokes Equations

Viscosity Revisited Viscosity is the internal friction of a fluid. Newton&#39;s law of viscosity: τ = μ × du/dy where τ is shear stress and du/dy is the velocity gradient. Fluids obeying this are...

⏱ 50 min read

Viscosity Revisited

Viscosity is the internal friction of a fluid. Newton's law of viscosity:

τ = μ × du/dy

where τ is shear stress and du/dy is the velocity gradient. Fluids obeying this are "Newtonian" (water, air, most gases and simple liquids). Non-Newtonian fluids (blood, ketchup, polymer melts) have more complex behavior.

Reynolds Number

The single most important dimensionless number in fluid mechanics:

Re = ρ V L / μ = V L / ν

It's the ratio of inertial forces to viscous forces:

  • Low Re (< 2300 in pipes): laminar
  • High Re (> 4000): turbulent
  • 2300-4000: transitional

The same geometry has the same behavior at the same Re, regardless of scale. This is why model testing in wind tunnels works.

The Navier-Stokes Equations

Newton's second law for a fluid element:

ρ (∂v/∂t + v·∇v) = -∇P + μ ∇²v + ρ g

This is a system of nonlinear partial differential equations. Solving them is one of the hardest problems in mathematics (one of the Millennium Prize problems).

Terms:

  • ρ ∂v/∂t: unsteady acceleration
  • ρ v·∇v: convective acceleration (nonlinear)
  • -∇P: pressure force
  • μ ∇²v: viscous force
  • ρg: gravity

Exact Solutions

For simple geometries, analytic solutions exist:

Couette flow: flow between two parallel plates, one moving. Linear velocity profile.

Poiseuille flow: flow through a circular pipe. Parabolic profile.

V(r) = (ΔP / (4 μL)) × (R² - r²)

Q = π R⁴ ΔP / (8 μL)

This is the Hagen-Poiseuille equation. Flow rate depends on R⁴ — doubling the pipe radius gives 16× the flow.

Stokes flow: very low Re, inertia negligible. Used for swimming microorganisms and sedimentation.

Boundary Layers

Near a solid surface, viscosity dominates in a thin layer called the boundary layer. Outside this layer, flow is essentially inviscid.

Boundary layer thickness grows as δ ~ √(νx/V). For air at 10 m/s over a 1 m plate, δ ≈ 5 mm.

Inside the boundary layer:

  • Velocity goes from 0 at the wall to V∞ at the edge
  • Shear stress at the wall causes drag

Laminar vs Turbulent Boundary Layers

Laminar: smooth, low drag (skin friction only).

Turbulent: chaotic, higher skin friction, but delays separation → less pressure drag.

This is why golf balls have dimples: they trip the boundary layer to turbulent, delaying separation, reducing total drag.

Separation and Drag

When the pressure gradient is adverse (pressure increasing along flow), the boundary layer can separate from the surface, creating a wake with low pressure behind the body → pressure drag.

Streamlined shapes delay separation; blunt shapes separate early.

Drag force:

F_D = ½ ρ V² C_D A

where C_D is the drag coefficient (from experiments or CFD).

Key Takeaways

  • Newton's law of viscosity: τ = μ du/dy
  • Reynolds number: Re = ρVL/μ
  • Navier-Stokes: nonlinear PDEs governing all fluid flow
  • Poiseuille: Q ∝ R⁴ for pipe flow
  • Boundary layers form near surfaces
  • Laminar vs turbulent boundary layers differ greatly
  • Drag depends on shape and Re
4

Pipe Flow and Head Loss

Laminar Pipe Flow For laminar flow in a circular pipe, the Hagen-Poiseuille equation gives: ΔP = 128 μ L Q / (π D⁴) The velocity profile is parabolic, with V_max = 2 × V_avg. This is a beautiful,...

⏱ 50 min read

Laminar Pipe Flow

For laminar flow in a circular pipe, the Hagen-Poiseuille equation gives:

ΔP = 128 μ L Q / (π D⁴)

The velocity profile is parabolic, with V_max = 2 × V_avg.

This is a beautiful, exact solution — but valid only for Re < 2300.

Turbulent Pipe Flow

For turbulent flow, no exact solution exists. We rely on:

  • Empirical correlations
  • Moody chart (or Colebrook equation)
  • Experimental data

The velocity profile is much flatter (almost uniform in the core, steep near the wall).

The Darcy-Weisbach Equation

The standard formula for head loss in a pipe:

h_L = f × (L/D) × (V² / 2g)

where:

  • f = friction factor (dimensionless)
  • L = pipe length
  • D = pipe diameter
  • V = average velocity
  • g = gravity

Head loss is energy lost to friction — measured in meters of fluid column.

Friction Factor

Laminar: f = 64 / Re (exact, from Poiseuille)

Turbulent (smooth pipe): f depends on Re

Turbulent (rough pipe): f depends on Re AND relative roughness ε/D

Moody Chart

The Moody chart plots f vs Re for various ε/D ratios. It's the most-used chart in fluid mechanics.

The Colebrook equation (implicit) gives the same result:

1/√f = -2 log₁₀(ε/(3.7D) + 2.51/(Re√f))

Solved iteratively or via approximations like Swamee-Jain:

f = 0.25 / [log₁₀(ε/(3.7D) + 5.74/Re^0.9)]²

Minor Losses

Fittings, valves, bends, and other components also cause head loss:

h_m = K × V² / 2g

where K is the loss coefficient (from tables):

  • 90° elbow: K ≈ 0.9
  • Tee (branch flow): K ≈ 1.8
  • Gate valve (open): K ≈ 0.2
  • Globe valve (open): K ≈ 10

Total head loss is the sum of major (friction) and minor (fittings) losses.

The Energy Equation for Pipes

Combining Bernoulli with losses:

P₁/γ + V₁²/2g + z₁ = P₂/γ + V₂²/2g + z₂ + h_L

where γ = ρg is the specific weight.

For a pump, add pump head h_p. For a turbine, subtract turbine head h_t.

Example: Water Supply Pipe

Water flows from a reservoir through 100 m of 50 mm cast iron pipe (ε = 0.26 mm) at a rate of 2 L/s. Find the head loss.

  1. Velocity: V = Q/A = 0.002 / (π × 0.025²) = 1.02 m/s
  2. Reynolds: Re = V×D/ν = 1.02 × 0.05 / 10⁻⁶ = 51,000 (turbulent)
  3. Relative roughness: ε/D = 0.26/50 = 0.0052
  4. From Moody chart: f ≈ 0.031
  5. Head loss: h_L = 0.031 × (100/0.05) × (1.02² / (2 × 9.81)) = 3.3 m

Plus fitting losses if there are bends, valves, etc.

Pumps and System Curves

A pump must overcome:

  • Static head (elevation difference)
  • Friction losses
  • Minor losses
  • Pressure difference

The system curve shows required head vs flow. The pump curve shows what the pump delivers. Their intersection is the operating point.

If the operating point is far from the pump's best efficiency point (BEP), efficiency drops and the pump may cavitate.

Key Takeaways

  • Laminar flow: exact solution (Hagen-Poiseuille)
  • Turbulent flow: empirical (Moody, Colebrook)
  • Darcy-Weisbach: h_L = f(L/D)(V²/2g)
  • Friction factor from Moody chart or Colebrook
  • Minor losses: h_m = K V²/2g
  • Pumps add head; system curve determines operating point
  • Cavitation occurs when local pressure drops below vapor pressure
5

Dimensional Analysis and Similarity

Why Dimensional Analysis? Experiments are expensive. If we can identify the dimensionless groups that govern a problem, we can: Reduce the number of variables Design scale models that predict...

⏱ 50 min read

Why Dimensional Analysis?

Experiments are expensive. If we can identify the dimensionless groups that govern a problem, we can:

  • Reduce the number of variables
  • Design scale models that predict full-scale behavior
  • Compare data across different systems

The Buckingham Pi Theorem

If a physical problem has n variables and m fundamental dimensions (M, L, T), there are n - m independent dimensionless groups.

Procedure:

  1. List all variables
  2. Express each in fundamental dimensions
  3. Choose m repeating variables (with independent dimensions)
  4. Form each Pi group from the remaining variables

Classic Example: Drag on a Sphere

Variables: F_D (force), V (velocity), D (diameter), ρ (density), μ (viscosity)

Dimensions: [M L T⁻²], [L T⁻¹], [L], [M L⁻³], [M L⁻¹ T⁻¹]

n = 5 variables, m = 3 dimensions → 2 Pi groups

Choose repeating variables: ρ, V, D

π₁ = F_D / (ρ V² D²) — this is the drag coefficient
π₂ = μ / (ρ V D) — this is 1/Re

So: F_D / (ρV²D²) = f(Re)

The drag coefficient depends only on Reynolds number. Thousands of experiments collapse to a single curve.

Important Dimensionless Numbers

Reynolds (Re) = ρVL/μ: inertial / viscous. Governs laminar vs turbulent transition.

Mach (Ma) = V/c: flow speed / speed of sound. Ma > 0.3 = compressible.

Froude (Fr) = V/√(gL): inertial / gravitational. Governs free-surface flows (ships, open channels).

Weber (We) = ρV²L/σ: inertial / surface tension. Governs droplet breakup.

Euler (Eu) = ΔP / ρV²: pressure / inertial. Used in pipe flow.

Prandtl (Pr) = μCp/k: momentum / thermal diffusivity. Governs heat transfer.

Nusselt (Nu) = hL/k: convective / conductive heat transfer. Governs heat transfer coefficients.

Similarity Requirements

For a scale model to represent a full-scale system, all relevant dimensionless groups must match.

Geometric similarity: same shape, scaled by factor L_r

Kinematic similarity: same velocity ratios everywhere

Dynamic similarity: same force ratios

In practice, we can't always match all groups. For ships, matching both Fr and Re is impossible at reduced scale — we prioritize Fr and correct for Re.

Modeling Example: Ship Resistance

A 1:50 scale ship model is tested in a towing tank. If the model's drag is measured, the full-scale drag is predicted by:

F_full = F_model × (ρ_full / ρ_model) × (L_full / L_model)³ × (C_D_full / C_D_model)

Since C_D is a function of Fr (matched) and Re (corrected via empirical formulas), we can compute full-scale drag from model tests.

Benefits of Dimensional Analysis

  • Reduces experiments dramatically
  • Reveals the physics via dimensionless groups
  • Enables scale modeling
  • Guides CFD validation
  • Universal — applies to heat transfer, structures, chemistry, biology

Key Takeaways

  • Buckingham Pi: n variables, m dimensions → n-m groups
  • Re, Ma, Fr, We, Pr, Nu are the key dimensionless numbers
  • Similarity requires matching the relevant groups
  • Scale models enable prediction of full-scale behavior
  • Dimensional analysis is universal across physics

📝 Problem Set 1: Hydrostatics, Bernoulli, Pipe Flow

Q1. Find the pressure at 20 m depth in water (ρ = 1000 kg/m³, g = 9.81 m/s²).

Show Solution

P = ρgh = 1000 × 9.81 × 20 = 196,200 Pa ≈ 196 kPa (gauge). Plus atmospheric = 296 kPa absolute.

Q2. Water flows through a pipe that narrows from 100 mm to 50 mm diameter. If velocity in the wide section is 1 m/s, find the velocity in the narrow section.

Show Solution

A1/A2 = (100/50)² = 4. So V2 = 4 × V1 = 4 m/s.

Q3. Water flows at 2 m/s through a 50 mm pipe that is 100 m long. If f = 0.02, find the head loss.

Show Solution

h_L = 0.02 × (100/0.05) × (4/19.62) = 0.02 × 2000 × 0.204 = 8.16 m.

🎯 Midterm 1: Hydrostatics, Bernoulli, Viscous Flow

Q1. A Pitot tube measures a pressure difference of 500 Pa in air (ρ = 1.2 kg/m³). What is the airspeed?

Show Solution

V = √(2ΔP/ρ) = √(2 × 500 / 1.2) = √833 = 28.9 m/s.

Q2. A sphere of radius 5 cm is dropped in oil (ρ=900 kg/m³, μ=0.5 Pa·s). Find the terminal velocity if sphere density is 2500 kg/m³.

Show Solution

At terminal velocity: F_buoy + F_drag = Weight. Stokes: F_drag = 6πμrv. Weight = (4/3)πr³ρ_s g. F_buoy = (4/3)πr³ρ_f g. So 6πμrv = (4/3)πr³g(ρ_s - ρ_f). v = 2r²g(ρ_s - ρ_f)/(9μ) = 2×0.0025×9.81×1600/(9×0.5) = 78.5/4.5 = 17.4 m/s.

Q3. A pump lifts water 20 m through a pipe. Find the minimum power required to move 10 L/s.

Show Solution

P = ρgQh = 1000 × 9.81 × 0.01 × 20 = 1962 W ≈ 2 kW. Add pump efficiency: if 70%, actual = 2.8 kW.