Reference topics: Berkeley EE105 Β· independent study notes, not affiliated

Analog Electronics

Bipolar and MOS transistors, single-stage and multi-stage amplifiers, frequency response, feedback, and op-amp design.

5Lectures
1Assignments
1Exams
45hDuration
1

Semiconductor Physics and the PN Junction

From Silicon to Transistor Silicon is a semiconductor: at absolute zero it is an insulator, at high temperature it conducts. Its four valence electrons form covalent bonds in a crystal lattice....

⏱ 50 min read

From Silicon to Transistor

Silicon is a semiconductor: at absolute zero it is an insulator, at high temperature it conducts. Its four valence electrons form covalent bonds in a crystal lattice. Doping introduces impurities:

  • N-type: add phosphorus (5 valence electrons) β€” extra free electrons
  • P-type: add boron (3 valence electrons) β€” holes (missing electrons)

When N-type and P-type silicon touch, electrons diffuse across the junction, leaving behind charged ions. The resulting depletion region has a built-in electric field that opposes further diffusion.

The Diode

A PN junction is a diode. Forward bias (P side +, N side -): the field is reduced, current flows. Reverse bias: the field grows, only leakage current flows.

The Shockley equation:

I = Is Γ— (e^(V/Vt) - 1)

where Is is the saturation current (10^-12 to 10^-15 A) and Vt = kT/q β‰ˆ 26 mV at room temperature.

At 0.7 V forward, the exponential is enormous: e^(0.7/0.026) β‰ˆ 10^12. This is why diodes "turn on" at ~0.7 V and act as a nearly-constant voltage drop.

Real Diode Behavior

  • Forward drop: 0.6-0.7 V (silicon), 0.2-0.3 V (Schottky), 1.8-3.4 V (LED)
  • Reverse breakdown: 5-1000 V depending on design (Zener)
  • Capacitance: junctions have parasitic capacitance, which limits high-frequency performance

Applications

Rectifier: convert AC to DC. A bridge rectifier uses 4 diodes.

Voltage reference: a Zener diode in reverse breakdown holds a stable voltage.

Protection: a diode across a relay coil absorbs the inductive kick.

Clamp: a diode limits a signal to a maximum voltage.

Small-Signal Model

For AC analysis, we linearize the diode around its DC operating point. The small-signal resistance is:

rd = Vt / Id

At Id = 1 mA, rd = 26 ohms. At Id = 10 mA, rd = 2.6 ohms.

This lets us treat the diode as a linear resistor for small AC signals β€” the key trick for analyzing amplifiers.

MOSFET Preview

A MOSFET is like a voltage-controlled resistor. The gate is separated from the channel by a thin oxide (insulator). Applying Vgs > Vth creates an inversion layer that conducts between source and drain.

Two modes:

  • Triode: Vds < Vgs - Vth, acts like a resistor
  • Saturation: Vds > Vgs - Vth, acts like a current source

The saturation current:

Id = (1/2) Γ— kn Γ— (W/L) Γ— (Vgs - Vth)Β²

This is the foundation of all analog and digital IC design.

Key Takeaways

  • Semiconductors are insulators until doped
  • A PN junction is a diode with 0.7 V forward drop
  • Shockley equation governs current-voltage relationship
  • Small-signal linearization is the key analysis trick
  • MOSFETs are voltage-controlled current sources
  • All of modern electronics rests on this foundation
2

MOSFET Large-Signal and Small-Signal Models

The MOSFET Structure A MOSFET has four terminals: Gate (G) β€” controls the channel Source (S) β€” where carriers enter Drain (D) β€” where carriers exit Body (B) β€” usually tied to source ...

⏱ 50 min read

The MOSFET Structure

A MOSFET has four terminals:

  • Gate (G) β€” controls the channel
  • Source (S) β€” where carriers enter
  • Drain (D) β€” where carriers exit
  • Body (B) β€” usually tied to source

The gate is separated from the channel by a thin oxide layer (SiOβ‚‚, ~2 nm for modern nodes). This makes the input impedance essentially infinite.

Threshold Voltage

Vth is the gate-source voltage needed to create a conducting channel. For modern MOSFETs, Vth β‰ˆ 0.3-0.7 V.

Below Vth (subthreshold): tiny current flows exponentially. This is the leakage current.

Above Vth: inversion layer forms, channel conducts.

Large-Signal Model

Triode region (Vds < Vgs - Vth):

Id = kn Γ— (W/L) Γ— [(Vgs - Vth) Γ— Vds - VdsΒ²/2]

This is a nonlinear resistor: for small Vds, it behaves like a resistor.

Saturation region (Vds > Vgs - Vth):

Id = (1/2) Γ— kn Γ— (W/L) Γ— (Vgs - Vth)Β² Γ— (1 + Ξ» Γ— Vds)

The channel is "pinched off" near the drain. Current depends mainly on Vgs, with a small dependence on Vds through the channel-length modulation parameter Ξ».

Transconductance gm

The small-signal gain of a MOSFET is its transconductance:

gm = βˆ‚Id/βˆ‚Vgs = kn Γ— (W/L) Γ— (Vgs - Vth) = 2Γ—Id / (Vgs - Vth)

At 1 mA and Vov = 0.2 V, gm = 10 mA/V.

Small-Signal Model

For AC analysis, replace the MOSFET with:

  • A resistor ro = 1/(Ξ» Γ— Id) from drain to source (output resistance)
  • A current source gm Γ— Vgs from drain to source
  • An open circuit from gate to source (infinite input impedance)

This gives the voltage gain of a common-source amplifier:

Av = -gm Γ— (ro || RD)

Common Configurations

Common Source: highest voltage gain, inverting, moderate input/output impedance. Most common.

Common Gate: current buffer, low input impedance, non-inverting.

Common Drain (Source Follower): voltage buffer, gain β‰ˆ 1, low output impedance. Used to drive heavy loads.

Cascode: common-source + common-gate stacked. Very high output impedance, high gain, good bandwidth.

Bias and Operating Point

Every MOSFET amplifier must be biased into saturation. Common techniques:

  • Fixed bias: resistor from VDD to gate. Simple, but sensitive to Vth variation.
  • Self-bias: source resistor with gate returned to ground. More stable.
  • Current-source bias: the workhorse of analog ICs. Stabilized by a current mirror.

Current Mirrors

The current mirror copies a reference current into multiple branches:

Iout = Iref Γ— (W/L)out / (W/L)ref

This is the fundamental building block of analog IC design. It provides a stable bias current independent of VDD.

Key Takeaways

  • MOSFET: voltage-controlled current source
  • Two regions: triode (resistor-like) and saturation (current source)
  • Small-signal model: gm and ro
  • Common configurations: CS, CG, CD, cascode
  • Current mirror is the universal bias building block
  • Analog design = biasing + small-signal analysis
3

Bipolar Transistors and Current Mirrors

The BJT Structure A Bipolar Junction Transistor has three terminals: Base (B), Collector (C), Emitter (E). Two junctions: base-emitter and base-collector. Current is carried by both electrons and...

⏱ 50 min read

The BJT Structure

A Bipolar Junction Transistor has three terminals: Base (B), Collector (C), Emitter (E). Two junctions: base-emitter and base-collector.

Current is carried by both electrons and holes (hence "bipolar"). The base is very thin and lightly doped.

Active Region

In active mode (BE forward, BC reverse):

Ic = Is Γ— e^(Vbe/Vt)
Ib = Ic / Ξ²

where Ξ² is the current gain, typically 100-300 for small-signal BJTs, 20-100 for power devices.

The base current is small but nonzero, unlike the MOSFET where gate current is essentially zero.

Transconductance

gm = Ic / Vt

At 1 mA, gm = 38 mA/V. This is the same transconductance formula as a MOSFET in weak inversion, and it's the maximum gm for a given current.

BJT vs MOSFET

| Property | BJT | MOSFET |
|----------|-----|--------|
| Control | Current (Ib) | Voltage (Vgs) |
| gm at 1 mA | 38 mA/V | 5-10 mA/V |
| Input impedance | Moderate (rΟ€) | Infinite |
| Noise | Lower | Higher |
| Matching | Poor (process) | Excellent |
| Speed | High (fT > 100 GHz) | High |

BJT is still used for:

  • High-speed circuits (RF, > 10 GHz)
  • Low-noise amplifiers
  • Bandgap voltage references
  • Some high-voltage applications

Current Mirrors

The BJT current mirror:

Iout = Iref Γ— exp((Vbe_out - Vbe_ref)/Vt)

If the two transistors are identical and at the same temperature:

Iout = Iref

Practical circuits add emitter resistors to reduce sensitivity to Vbe mismatch.

Differential Pair

The differential pair is the input stage of every op-amp. Two matched transistors with a shared tail current source.

Differential input: V+ - V-. Output: current difference.

Common-mode input: affects both equally β€” rejected by symmetry.

The tail current source is the key: it "steers" the tail current to one side or the other depending on the differential input.

Key Parameters

  • gm: transconductance
  • rΟ€: small-signal input resistance = Ξ²/gm
  • ro: output resistance = VA/Ic (VA is the Early voltage, typically 50-200 V)
  • fT: transition frequency β€” where current gain drops to 1

Applications

Bandgap reference: combines a BJT's predictable Vbe (~600 mV, -2 mV/Β°C) with a PTAT current (proportional to absolute temperature) to produce a stable 1.2 V reference.

Gilbert cell: a mixer that multiplies two analog signals. Foundation of all RF receivers.

Current feedback amplifier: high slew rate, used in video and RF.

Key Takeaways

  • BJTs are current-controlled, MOSFETs are voltage-controlled
  • BJT has higher gm for the same current
  • Current mirrors copy a reference current
  • Differential pair is the input of every op-amp
  • Modern analog ICs use both: BJT where speed/noise matters, MOS elsewhere
4

Operational Amplifiers and Feedback

The Ideal Op-Amp An op-amp is a differential amplifier with very high gain. Ideal properties: Infinite open-loop gain (A β†’ ∞) Infinite input impedance (no current into inputs) Zero output impedance...

⏱ 50 min read

The Ideal Op-Amp

An op-amp is a differential amplifier with very high gain. Ideal properties:

  • Infinite open-loop gain (A β†’ ∞)
  • Infinite input impedance (no current into inputs)
  • Zero output impedance
  • Infinite bandwidth

Real op-amps (e.g., LM741, TL071, OPA192) approximate these:

  • A = 10^5 to 10^7
  • Input impedance: 10^6 (bipolar) to 10^12 (CMOS)
  • Output impedance: 10-100 ohms
  • Unity-gain bandwidth: 1-100 MHz

The Golden Rules

For an op-amp in negative feedback:

  1. The output does whatever it takes to make the two inputs equal (virtual short)
  2. No current flows into the inputs

These two rules let you analyze any op-amp circuit.

Inverting Amplifier

Vin ──R1──┬── (βˆ’)
β”‚
β”‚
(βˆ’) op-amp
β”‚
└──R2── Vout

(+): GND

Virtual ground at the (βˆ’) input (since + is at 0 V). Current through R1: I = Vin/R1. This current must flow through R2 (no current into op-amp input). So Vout = -I Γ— R2 = -Vin Γ— R2/R1.

Gain = -R2/R1

Non-Inverting Amplifier

Vin ── (+)
op-amp
(βˆ’)──R1──GND
β”‚
└──R2── Vout

Virtual short: V(-) = V(+). So V(-) = Vin. Voltage divider from Vout to GND through R1 and R2:

Vin = Vout Γ— R1/(R1+R2)

Gain = 1 + R2/R1

Buffer (Voltage Follower)

Vin ── (+)
op-amp
(βˆ’)──┐
└── Vout

Gain = 1. Used to convert a high-impedance source to a low-impedance output. Perfect for driving heavy loads.

Integrator

Vin ──R1──┬── (βˆ’)
β”‚
C
β”‚
└── Vout

Vout = -(1/(R1Γ—C)) Γ— ∫Vin dt

Applications: analog filters, charge amplifiers, ADCs.

Differentiator

Capacitor at input, resistor at feedback. Vout = -RC Γ— dVin/dt.

Filters

Combine R, C, and op-amp to build:

  • Low-pass: gain drops above cutoff
  • High-pass: gain drops below cutoff
  • Band-pass: combination
  • Notch: rejects one frequency

The Sallen-Key topology gives a 2nd-order filter with one op-amp.

Real Op-Amp Limitations

Input offset voltage: a few Β΅V to a few mV. Limits DC precision.

Input bias current: nA (bipolar) to pA (CMOS). Causes offsets through source resistance.

Gain-bandwidth product (GBW): the closed-loop bandwidth is GBW / |Gain|. At 100 MHz GBW, a gain of 10 gives 10 MHz bandwidth.

Slew rate: max dVout/dt. Typically 1-20 V/Β΅s. Limits large-signal bandwidth.

Common-mode range: inputs must stay within a range near the rails. Rail-to-rail op-amps extend this.

Output swing: how close Vout can get to the rails. Rail-to-rail output is 50 mV from each rail.

Key Takeaways

  • Ideal op-amp: infinite gain, infinite Zin, zero Zout
  • Golden rules: virtual short, no input current
  • Inverting: -R2/R1, Non-inverting: 1+R2/R1
  • Integrator and differentiator are workhorses
  • Real op-amps have offset, bias current, finite GBW, slew rate
  • Choose op-amp based on: speed, precision, power, cost
5

Analog Filter Design

Why Filters? Every real signal has noise. Filters separate signal from noise based on frequency content: Low-pass: keeps low frequencies, removes high (smoothing, anti-aliasing) High-pass: keeps h...

⏱ 50 min read

Why Filters?

Every real signal has noise. Filters separate signal from noise based on frequency content:

  • Low-pass: keeps low frequencies, removes high (smoothing, anti-aliasing)
  • High-pass: keeps high, removes low (AC coupling, removing DC offset)
  • Band-pass: keeps a band (radio receivers, audio equalizers)
  • Notch: removes a narrow band (60 Hz hum rejection)

First-Order RC Low-Pass

Vin ──R──┬── Vout
β”‚
C
β”‚
GND

Transfer function:

H(jω) = 1 / (1 + jωRC)

Cutoff frequency (where |H| = 0.707):

fc = 1 / (2Ο€RC)

Roll-off: -20 dB/decade. At 10x fc, gain is -20 dB; at 100x fc, gain is -40 dB.

Second-Order Filters

Two RC sections in series don't work well β€” they load each other. Use an active filter (Sallen-Key):

Vin ──R1──┬──R2──┬── (+)
C1 β”‚ op-amp
β”‚ C2 β”‚
GND GND └── Vout
β”‚
(βˆ’)──R3──R4──GND

The op-amp buffers and provides the feedback that creates the sharp roll-off.

Roll-off: -40 dB/decade (10x better than first-order).

Butterworth Response

Maximally flat passband. No ripple. The standard "textbook" response.

For 2nd order:
H(s) = Ο‰cΒ² / (sΒ² + √2 Ο‰c s + Ο‰cΒ²)

The Q factor is 0.707.

Chebyshev Response

Ripple in the passband, but sharper roll-off than Butterworth.

For 0.5 dB ripple, Q = 1.4 for 2nd order.

Trade-off: more ripple = sharper roll-off = worse transient response.

Bessel Response

Linear phase (constant group delay) β€” important for pulses and digital signals.

Roll-off is gentler than Butterworth.

Higher-Order Filters

Cascade multiple 2nd-order sections. A 4th-order filter is two 2nd-order sections in series. A 6th-order is three.

Real components have tolerance, so higher-order filters are harder to build.

Active Filter Design Example

Design a 2nd-order Butterworth low-pass at 1 kHz.

Given: fc = 1 kHz, Q = 0.707, C = 10 nF

R = 1 / (2Ο€ Γ— 1000 Γ— 10 nF) = 15.9 kΞ©

Use standard values: R = 16 kΞ©, C = 10 nF, and a second stage with R = 16 kΞ©, C = 4.7 nF for the Sallen-Key topology.

Filter Order and Roll-off

| Order | Roll-off | Components |
|-------|----------|------------|
| 1st | -20 dB/dec | 1 R, 1 C |
| 2nd | -40 dB/dec | 2 R, 2 C, op-amp |
| 4th | -80 dB/dec | 4 R, 4 C, 2 op-amps |
| 6th | -120 dB/dec | 6 R, 6 C, 3 op-amps |

For each additional 20 dB of stopband attenuation, add one order.

Anti-Aliasing Filters

Before sampling an analog signal, you must low-pass filter it to remove frequencies above Nyquist (fs/2). Otherwise, aliasing folds high frequencies into the baseband, corrupting the signal.

Rule: cutoff at 0.4 Γ— fs, sharp enough that fs/2 is attenuated by >60 dB.

Key Takeaways

  • Filters separate signal from noise by frequency
  • First-order: -20 dB/dec, simple RC
  • Second-order: -40 dB/dec, needs op-amp
  • Butterworth (flat), Chebyshev (ripple), Bessel (linear phase)
  • Higher order = cascaded 2nd-order sections
  • Anti-aliasing filter is mandatory before ADC

πŸ“ Problem Set 1: MOSFETs, BJTs, Amplifiers

Q1. A MOSFET has kn' = 100 Β΅A/VΒ², W/L = 20, Vth = 1V, Vgs = 2V, Ξ» = 0. Find Id and gm in saturation.

Show Solution

Vov = Vgs - Vth = 1V. Id = 0.5 Γ— 100e-6 Γ— 20 Γ— 1Β² = 1 mA. gm = 100e-6 Γ— 20 Γ— 1 = 2 mA/V.

Q2. Design a common-source amplifier with gain -20 using a MOSFET with gm = 5 mA/V, ro = 100 kΞ©. Choose RD.

Show Solution

Want -20 = -5m Γ— (RD || 100k). RD || 100k = 4 kΞ©. Solve: RD = 4k Γ— 100k / (100k - 4k) = 4.17 kΞ©. Choose RD = 4.3 kΞ© standard value.

Q3. For a BJT current mirror with Iref = 1 mA, Ξ² = 100, and identical transistors, what is Iout? What happens if Ξ² drops to 50?

Show Solution

Iout = 1mA Γ— 1/(1+2/100) = 0.98 mA. For Ξ²=50: Iout = 1 Γ— 1/(1+2/50) = 0.96 mA. Difference is small β€” current mirrors are robust to Ξ² variation.

🎯 Midterm 1: MOSFET, BJT, Amplifiers

Q1. Explain the difference between triode and saturation regions of a MOSFET. Which is used for amplification?

Show Solution

Triode (Vds < Vov): acts like a voltage-controlled resistor, Id depends on both Vgs and Vds. Saturation (Vds > Vov): Id depends mainly on Vgs, channel is pinched off at drain. Saturation is used for amplification because it gives high gain (Id independent of Vds β†’ high ro).

Q2. Design a differential pair with tail current 1 mA and gain 20. Assume gm = 2 mA/V per transistor and ro = 50 kΞ©.

Show Solution

Differential gain = gm Γ— (ro || RD). Want 20 = 2m Γ— (50k || RD). 50k || RD = 10 kΞ©. RD = 12.5 kΞ©. Choose 12 kΞ© standard.

Q3. For a common-emitter amplifier with Rc = 5 kΞ©, gm = 40 mA/V, ro = 100 kΞ©, Ξ² = 200, find the voltage gain.

Show Solution

Av = -gm Γ— (Rc || ro) = -0.04 Γ— (5k || 100k) = -0.04 Γ— 4.76k = -190. Very high gain.